Noctua NH-L12 Installation Manual AMD Removing the retention module Dear customer, Congratulations on choosing the Noctua NH-L12. This smaller size cooler packs all essential technologies of our award-winning high-end models into a highly compact package in order to give you the best possible quiet cooling experience for HTPCs and small form factor builds. I’m confident that you will be able to sense some of the research, attention and care we’ve put into making this product. Enjoy your NH-L12!
Yours sincerely, Roland Mossig, Noctua CEO This manual will guide you through the installation process of the SecuFirm2™ mounting system step by step. Prior to installing the cooler, please consult the compatibility list on our website (www.noc- tua.at/compatibility) and verify that the cooler is fully compatible with your motherboard. Should you encounter any difficulties, please check the FAQs on our website (www.noctua.at/faqs) and don’t hesitate to contact our support team at [email protected]. Noctua cannot be held responsible for any damage or losses caused by compatibility issues. Multilingual versions of this manual are available on our website: www.noctua.at/manuals The NH-L12 can be used with both fans for maximum performance or with the NF-B9 fan only in order to reduce the total height to 66mm: If you want to use both fans, put the NF-F12 fan back on. If you don’t run the NF-F12 on the CPU cooler, you can use the supplied fan screws or silicone Vibration-Compensators to install it inside your case.
![Decodificador l12 Decodificador l12](/uploads/1/2/5/4/125468583/533480886.jpg)
Step 1 step 2 Fan Setup Step 5 Step 1 Required mounting parts: 4x NM-APS1 Plastic Spacer 2x NM-AMB1 Mounting-Bars 4x NM-ALS1 Long Screw Caution: The SecuFirm2 tm mounting system requires a backplate, which is preinstalled on most AMD mainboards. If your mainboard doesn’t have a backplate, please contact our support team at [email protected]. Caution: Make sure that the curved sides of the mounting bars are pointing inwards.
View and Download DirecTV L12 user manual online. L12 Receiver pdf manual download. The NH-L12 is a low-profile quiet cooler designed for use in small form factor cases and HTPC environments. While it provides first rate performance in its class, it is not suitable for overclocking and should be used with care on CPUs with more than 95W TDP (Thermal Design Power).
![Manual Manual](https://http2.mlstatic.com/D_Q_NP_942803-MLV26745865568_022018-X.jpg)
Caution: Tighten the screws until they stop. If your mainboard uses a retention module for CPU cooler installation, please remove it first. The SecuFirm2 tm mounting system will install di- rectly to your mainboard’s stock backplate on the rear side of the socket.
AMD stock backplate Caution: Tighten the screws until they stop. Applying thermal paste If there are residual traces of thermal paste or thermal pads on your CPU, please clean them off first. Then press a small drop (4-5mm diameter) of NT-H1 onto the centre of the heatspreader. Step 3 Even with high-grade products and strict quality control, the possibility of defects cannot be eliminated entirely.
Therefore, we aim at providing the highest possible level of reliability and convenience by offering a war- ranty period of 6 years and direct, fast and straightforward RMA service. Should you encounter any problems with your NH-L12, please don’t hesitate to contact our support team ([email protected]). Please also consult the FAQ section on our website: www.noctua.at/faqs. Warranty, Support and FAQs Connect the fan(s) to the mainboard. Use the supplied NA-YC1 y-split cable to connect both fans to one fan header.
Depend- ing on your CPU and the temperature inside the case, you may interconnect the supplied NA-RC6 and NA-RC7 Low-Noise Adapters (L.N.A.) in order to further reduce the fans operating noise. Use the NA- RC6 for the NF-F12 120mm fan and the NA-RC7 for the NF-B9 92mm fan.
Caution: Never use one adaptor for both fans by putting it before the y-split cable. Caution: When using the L.N.A., check the temperature of your CPU using appropriate software (e.g. The respective applications of your mainboard manufacturer), in order to evade automatic throttling of the CPU due to the increased temperature. If the cooling performance is insufficient, please increase case ventilation or remove the L.N.A. Caution: Applying too much thermal paste will lower the heat conductivity and cooling performance! Fastening the heatsink to the CPU Caution: Please first take off the protection cover at the bottom side of the heatsink and remove the rubber support bar between the bottom fan and the base of the heatsink! Take off the top fan.
Then put the heatsink onto the CPU and screw it to the screw threads of the mounting bars. Note that you can reach through the blades of the lower fan using the supplied screw driver. There is thus no need to take off the lower fan for installation. Step 4 First put the plastic spacers onto the screw threads, then fix the mounting bars using the 4 long screws. Attaching the mounting bars Step 2 Mainboard Fans Low-Noise Adaptor Y-Split Cable Y-Split Cable Low-Noise Adaptors Dual fan mode (height 93mm) Single fan mode (height 66mm).
Dek 6 years ago 6 years ago Is anyone willing to share the pinouts for Philips ultrasound probes? FEATURES. 12 to 5 MHz extended operating frequency range. Fine pitch, high resolution linear array. 50 mm effective aperture length. 10° of trapezoidal imaging. Steerable pulsed wave, color Doppler, and Color Power Angio, Panoramic, SonoCT, XRES, and harmonic imaging.
High resolution superficial applications including vascular, small parts, breast, and musculoskeletal imaging. Contrast applications. Elastography (iU22 system only). Supports biopsy guide capabilities SPECIFICATIONS Frequency Range 5 to 12 MHz.